冷再生機在工作過程中，每次停車，即使只需要幾分鐘就可以更換罐車，也會對整個接縫處回收材料的均勻性造成嚴重影響。因此，冷再生機租賃廠家提醒，在施工中應盡量減少停工。在不可避免的情況下，應仔細處理形成的橫向接縫。

During the working process of the cold regenerator, even if the tank car can be replaced within a few minutes after each stop, it will also have a serious impact on the uniformity of the recycled material at the entire joint. Therefore, the cold regenerator leasing manufacturer reminded that shutdown should be minimized during construction. Where unavoidable, the transverse joints formed shall be carefully treated.

1。當臨時停工后重新開工時，整個再生裝置應后退1.5-2米再生材料，以確保所有材料在開工后得到處理。

1。 When restarting after temporary shutdown, the whole regeneration device shall be retreated 1.5-2 meters to the recycled material to ensure that all materials are treated after starting.

2。后一個工段應預留4-6米的實時壓路，下一工段不碾壓。

2。 4-6 meters of real-time rolling shall be reserved for the next section, and the next section shall not be rolled.

3。當冷再生租賃后開始工作時，應將轉子切割到再生層的底部，以破壞再生材料。前進速度為0，使松散再生料混合不均勻。因此，人工翻身后須對坑進行平整。

3。 When starting work after the cold regeneration lease, the rotor should be cut to the bottom of the regeneration layer to destroy the regeneration material. The forward speed is 0, so that the loose recycled material is mixed unevenly. Therefore, the pit must be leveled after manual turnover.

再生層穩定后，再生料基本處于穩定狀態，但不能完全再生機輪軌。此時輪距深度約為0.5-1厘米。

After the regeneration layer is stabilized, the recycled material is basically in a stable state, but the wheel rail of the regeneration machine cannot be completely eliminated. At this time, the track depth is about 0.5-1 cm.

當兩段再生完成且全部穩定后，用平地機進行平整。一次調平的目的是一和二塊右側的三排輪軌。二次平整主要是在刮料機前均勻攤鋪再生料，同時考慮再生層的水平和垂直坡度。后對整個作業段進行平整。

When the two stages of regeneration are completed and all are stable, use a grader to level them. The purpose of primary leveling is to eliminate one and two right three-row wheel tracks. The secondary leveling is mainly to evenly spread the recycled material in front of the scraper, taking into account the horizontal and vertical slope of the recycled layer. After that, the whole operation section shall be leveled.

再生機的工作寬度一般小于再生路面的工作寬度。因此，整個道路的再生需要多次操作，導致幾個相鄰工作面之間出現縱向接縫。

The working width of the regenerator is generally smaller than the working width of the recycled pavement. Therefore, the regeneration of the entire road requires multiple operations, resulting in longitudinal joints between several adjacent working faces.

一般來說，相鄰工作面之間的小重疊為10cm，以確保縱向接縫處回收材料的連續性，同時避免相鄰工作面之間存在不回收的夾帶。

Generally speaking, the small overlap between adjacent working faces is 10cm to ensure the continuity of recycled materials at the longitudinal joints and to avoid non-recycled entrainment between adjacent working faces.

另外，在選擇冷再生機的時候，要與冷再生租賃廠家簽訂相應的合同，這一點是非常重要的。您要注意一下合同的雙方，甲方與乙方都應該是明確的租賃人，應該明確雙方的責任和義務。更多相關該設備租賃的事項就來我們網站做http://ispycorp.com咨詢吧！

In addition, when selecting the cold regeneration machine, it is very important to sign the corresponding contract with the cold regeneration leasing manufacturer. You should pay attention to both parties of the contract. Both Party A and Party B should be clear tenants, and the responsibilities and obligations of both parties should be clear. Come to our website for more matters related to the equipment leasing http://ispycorp.com Ask!